Notifications
Clear all
| Posts with their shortened content | ||
 |
RE: Sv103xs work in progress
By Goldrod, 56 minutes ago
Forum
Daiwa
|
|
| I haven’t messed with this platform in a while but it’s certainly one of my favorites. Personally the 7.9:1 is good for me but seeing how you went with a higher gear ratio yet still retaining the stoc... | ||
|
|
RE: More Evergreen rods popping up
By Goldrod, 1 hour ago |
|
| Gas or an evergreen rod ? easy answer FISH ON 😆 looking forward to some new stuff, Milwaukee is not doing it for me anymore 😆 | ||
 |
RE: 10 oz ain't what it used to be
By RISE, 14 hours ago
Forum
Bait Finesse
|
|
| Always being original. Love it, my bruddah. | ||
|
|
RE: Steez gears into Type R+
By RISE, 14 hours ago
Forum
Reel Tuning and Mods
|
|
| @triple_illusion I want to help, but I’m away camping/fishing for the week. | ||
 |
RE: Yuki Itö with another Red Dot design award…
By HKBasser, 16 hours ago |
|
| @rise the award is probably fixed, megabass has definitely been more mega(b)ass recently. On the subject of onetens, I’ve stopped buying them, I don’t know if it’s a bad batch or whatever but I’ve ha... | ||
 |
RE: JDM Daiwa Steez Real Control 6'11" casting
By BlitzDR, 19 hours ago
Forum
Baitcasting
|
|
| Okay, finally had a LOT of time with this rod. Today 4 LMB, 1 a bit over 8 lbs, 1 about 3 1/2, 1 about 2 and 1 about a 1 3/4 lbs. All on the Evergreen One's Bug, A II reel. Here's the pix: Attach... | ||
 |
RE: Standard Plus Handles–Knob Post Removal
By triple_illusion, 2 days ago
Forum
Reel Tuning and Mods
|
|
| Update: a 1.5mm allen wrench sufficed to loosen the screw on the back of the handle. I measured the hex bolt with calipers and it comes in at about 1.8mm. That is virtually unheard of, standard increm... | ||
|
|
RE: Steez gears into Type R+
By triple_illusion, 2 days ago
Forum
Reel Tuning and Mods
|
|
| I was mistaken on the small metal gear from the Steez (G75-6101). I thought it needed the flat spots on the inside hole to pair with the drive shaft. But there are two compatibility issues: it is both... | ||
|
|
RE: Sv103xs work in progress
By dragon1, 5 days ago
Forum
Daiwa
|
|
| There's more wraps and rotations of line on a smaller width of the spool with the faster gear ratio. This tends to happen after a faster gear ratio is installed. I test casted for a couple hours yeste... | ||
|
|
RE: Sv103xs work in progress
By dragon1, 5 days ago
Forum
Daiwa
|
|
| Dropped 8.1 brass gears and Pixy Carbontex + washers set into my SV103L. Works great...the wormgear is still the 6.3, but it seems to work well enough and cast just fine with 15lb Izorline Platinum. ... | ||
|
|
RE: Yuki Itö with another Red Dot design award…
By triple_illusion, 7 days ago |
|
| I still maintain that my fishing skill level increased exponentially due to G-Loomis blank sensitivity. I don't have any of their new offerings because I can't stand their handle designs, placement of... | ||
|
|
RE: Steez gears into Type R+
By triple_illusion, 7 days ago
Forum
Reel Tuning and Mods
|
|
| I think I have it figured....will update as soon as I have parts in hand. | ||
|
|
RE: Yuki Itö with another Red Dot design award…
By BlitzDR, 1 week ago |
|
| How many guys still use Loomis because Grandad had one? | ||
 |
RE: Yuki Itö with another Red Dot design award…
By Good Times, 1 week ago |
|
| Recency bias for some reason won't go away. Cutting edge at one time, but that time is past. MB's OG reel offerings were legit. The sticks hit or miss, just being honest, and my personal complaint of ... | ||
|
|
RE: Steez gears into Type R+
By dragon1, 1 week ago
Forum
Reel Tuning and Mods
|
|
| Following because I want to know as well. | ||
Page 1 / 6
Next
